• Free Delivery
  • No Credit Checks
  • £0 Maintenance Costs

Beko Washing Machine Fault Codes

Beko Washing Machine Fault Codes

E1 - Heating issue.

Issue: There could be an issue with the wiring or the thermistor identified by the NTC sensor that connects to the heater element.
Fix: There is no easy fix for this fault, please follow this link to our Washing Machine and Tumble Dryer Rental page.

E2 - Heating issue.

Issue A problem with the heater is being detected here with water not heating properly and this could be a wiring issue or a defective heater.
Fix: There is no easy fix for this fault, please follow this link to our Washing Machine and Tumble Dryer Rental page.

E3 - Heating issue.

Issue: This is a problem with the heater indicating that there’s a constant stream of heat and is again a wiring issue or a faulty control relay to the heater.
Fix: There is no easy fix for this fault, please follow this link to our Washing Machine and Tumble Dryer Rental page.

E4 - Water fill issue.

Issue: When your appliance can’t fill this error code will display caused by problems with the water inlet valve, the door not securing properly, or a faulty printed circuit board (PCB).
Advice: Check the water fill hose is not kinked, and check the water feed tap is on.
Fix: 
If the above advise has not fixed the issue then it may be the inlet valve is faulty, there is no easy fix for this fault, please follow this link to our Washing Machine and Tumble Dryer Rental page.

E5 - Drain issue.

Issue: Beko washing machine error code E05 indicates that your appliance is unable to drain which may be related to an obstruction in the pump filter or drain hose, or a defective drain pump.
Advice: Please check for blockages in your pump filter, a more detailed guide can be found here. Also check for any blockages in waste water hose and in any under-sink plumbing.
Fix:
If none of the above solutions work, it is likely you have a pump failure please follow this link to our Washing Machine and Tumble Dryer Rental page.

E6 - Motor issue.

Issue: This error code means that there’s a fault with the motor resulting in your appliance not being able to complete its cycle. The fault could lie with the motor mechanism, the wiring, or the PCB.
Fix: There is no easy fix for this fault, please follow this link to our Washing Machine and Tumble Dryer Rental page.

E7 - Level sensor issue.

Issue: If your washing machine is experiencing a problem with the level sensor this code will display. It can cause your appliance to empty near the beginning of the cycle or not even start a cycle at all.
Fix: There is no easy fix for this fault, please follow this link to our Washing Machine and Tumble Dryer Rental page.

E8 - Water fill issue.

Issue: Beko washing machine error code E08 is typically related to not filling with water and can be caused by a faulty water valve, a problem with the antiflooding mechanism, or issues with wiring or the PCB.
Advice: Check the water fill hose is not kinked, and check the water feed tap is on.
Fix: If the above advise has not fixed the issue then it may be the inlet valve is faulty, there is no easy fix for this fault, please follow this link to our Washing Machine and Tumble Dryer Rental page.

E9 - Door lock issue.

Issue: When problems occur with the door lock error E9 will show. This could be the lock itself, or the electronics that operate the lock. Alternatively, it could be a PCB issue.
Fix: There is no easy fix for this fault, please follow this link to our Washing Machine and Tumble Dryer Rental page.

E10 - Door lock issue.

Issue: This code will display when your washing machine is detecting that the door is jammed. It may be due to a broken lock or latch, or a problem with the electrics.
Fix: There is no easy fix for this fault, please follow this link to our Washing Machine and Tumble Dryer Rental page.

E11 - Motor Issue

Issue: Beko washing machine error code E11 is indicating that there’s a problem with the motor which could be quite complex and related to wiring, the PCB, or the motor itself.
Fix: There is no easy fix for this fault, please follow this link to our Washing Machine and Tumble Dryer Rental page.

E17 - Over foaming issue.

Issue: If your washing machine detects that there’s an excess amount of foam detected in your washing machine this error code will display.
Fix: Running additional rinse cycles may help to clear the foam and to stop this from happening. In the future change to a recommended detergent and use the specified quantity.

E18 - Unbalanced load issue

Issue: When an unbalanced load has been identified your washing machine may stop during the spin cycle.  This issue may also arise if the feet are unlevel.
Fix: Reloading your appliance and then restarting should solve this problem. Furthermore, levelling all the feet on the appliance will help.

Still need help? Please send a message or call 01206 794905 to discuss with an agent.

Added by: Alistair Gorbutt

Added in: Washing Machine Support Beko Washing Machine Faults

Recently Added

Beko Tumble Dryer Fault Lights

Beko Tumble Dryer Fault Lights

Added by: Alistair Gorbutt

Bosch Tumble Dryer Fault Codes

Bosch Tumble Dryer Fault Codes

Added by: Alistair Gorbutt

Hotpoint Tumble Dryer Fault Codes

Hotpoint Tumble Dryer Fault Codes

Added by: Alistair Gorbutt